At A Glance

Ademco Vista Panels - Quick Reference

Arm:	Code + [2] Away (Arms All); Code + [3] Stay (Arms Perimeter only)
DisArm:	Code + [1] OFF
Check Faulted Zones	Press [*] key.
Smoke Reset:	Smoke Detectors mostly reset automatically with these panels when alarm is silenced. However, the user may have to enter Code + [1] OFF again to reset the smokes. There might be a reset button on some panels for 4-wire smokes.
Code Change:	Code + [8] Code + User # + 4 new digits. Most panels require a 2-digit user number. Vector panels, Vista 10, 4110 and 4120 panels have 1-digit user numbers. Larger panels require alpha keypads and will ask questions to complete after the above process is done.
Chime Mode On/Off:	Code + [9] Chime
Bypass Zone(s):	Code + [6] + Zone number(s). Most panels use 2-digit zone numbers. The very large Vista 100 and Vista 128 panels use 3-digit zone numbers.
Power Down Panel:	Pull one wire from NP7-12 or NP4-12 battery, pull one AC wire. Most panels this will be terminal 1 on the far left bottom of panel. Some panels vary. Vector panels - AC is term. 3 & 4.

Ademco 1021, 1023, 1024, 1025, 1026 Panels - Quick Reference

Ademco 215	Ademco 5240a	Ademco 5212

Panels: Ademco 1023, 1024, 1025, 1026 Arm: [4-digit code] Blinking red light=Ready To Arm; Solid red light=Armed; Red Light Off=Faulted zone Disarm: [4-digit code] Check Faulted Zones: If a zone is faulted, the red light will not be blinking on the keypad. Check control panel lights. Usually has Basic Prot 1, Basic Prot 2 and Delay zones. Faulted zone(s) will be lit. Change code: Must be done on site - change jumpers on keypad 216 adapter in the panel. Pictured here is 5213 adapter, but it works the same as the 216. Power down panel: Pull plug on 496 battery, disconnect terminal 17 or 18 (AC power).	Panels: Ademco 1021 Arm: [4-digit code] Disarm: [4-digit code] Check Faulted Zones: If a zone is faulted, the green light will not be lit on the keypad. Check control panel lights. Usually has Basic Prot 1, Basic Prot 2 and Delay zones. Faulted zone(s) will be lit. Lights: Green light on=Ready to Arm; Red light on=Armed Change code: Must be done on site - change jumpers on back of keypad. Power down panel: Pull plug(s) on battery(s). Most of these are 12 volt panels. There will be either 2 496 batteries or an NP4-12. Disconnect AC -- far right terminal on bottom terminal strip, left side of panel. (There is a 6-volt version of this keypad [5241] that works with the 1023, 1024, 1025 and 1026 panel. It operates the same as this one. Most of these will be 12 volt 1021 panels.)	Panels: Ademco 1023, 1024, 1025, 1026 Arm: [4-digit code] Disarm: [4-digit code] Check Faulted Zones: If a zone is faulted, the green light will not be lit on the keypad. Check control panel lights. Usually has Basic Prot 1, Basic Prot 2 and Delay zones. Faulted zone(s) will be lit. Lights: Green light on=Ready to Arm; Red light on=Armed; Yellow light on=Shunt. Arm with Shunt (yellow light): Press any key other than first digit of code, then enter code. Change code: Must be done on site - change jumpers on keypad 5213 adapter in the panel. Power down panel: Pull plug on 496 battery, disconnect terminal 17 or 18 (AC power).

Ademco 4150 - Quick Reference

Arm:	Code
DisArm:	Code
Check Faulted Zones	Press [ZONE DISPLAY] key. While holding this button down, lights become zone lights. On is faulted, off is normal, blinking is alarm memory.
Smoke Reset:	Press [CMND], then press [TEST RESET]. After 15 seconds, snoke detectors will reset.
Code Change:	Master code is burned onto the chip and can only be changed by technician. User 1 and User 2 code can be added at keypad. To add or change a temp code, press [CODE] button (the button on the older black keypad says [PROGRAM])+ master code + User # (1 or 2) + New 4 digit code.
Chime Mode On/Off:	[CMND] + [CHIME] (9 key).
Bypass Zone(s):	[CMND] + [BYPASS] (6 key) + optionally zone(s) to bypass + [CMND]. Then enter code to arm. If you leave out zone(s) to bypass, the panel will bypass faulted zones automatically.
Power Down Panel:	Either uplug transformer or disconnect terminal 4 or 5 on right side of panel board. Unplug one side of battery (usually an NP4-12 installed).

DSC / Moose - Quick Reference

DSC Alpha

Moose LED

Panels: Larger DSC Panels - 5010 User, Installation
Arm: Enter Code OR Press Stay or Away button for
2 seconds
Disarm: Enter Code
Check Faulted Zones: Press [>] key to scroll through open zones.
Change code: [*][5][Master Code][user number 01 to 32][new access code].
Press the [#] key to exit the Menu.
Power down panel: Pull one wire off battery. Disconnect wire on far left terminal on terminal strip. (Set up like a Vista panel -- 1st 2 terminals on left are AC power.)
Fire Alarm and Smoke Reset:

PC1000 Enter code to silence fire alarm. Press [*][7] to reset smoke detectors.	PC2550 Press [#] to silence alarm Press [*][4] (hold down the 4 for several seconds) to reset smoke detectors.	DSC4020 Enter valid code to silence, then Enter valid code to reset smokes.
PC1550 Press [#] to silence Press [*][7] to reset smokes.	DSC4010 Enter access code to silence alarm. Press [*][4] to reset smokes.	PC5010 (Power 832) Press [#] to silence With LED keypad, press [][7][2] to reset smokes. With alpha keypad, press [] to enter Function List > scroll with arrow keys to find "Output Control" > The display will read "Select Output" > Scroll with arrow keys to find "Sensor Reset" > press the [*] key to reset smokes.

Panels: Moose Z1100
User manuals:
Z1100 System 1, Z1100 System 2, Z1100E
Installation Manuals:
Z1100 System 1, Z1100 System 2, Z1100E
(All 3 of these work practically identically)
Arm: Press [1] plus code.
Disarm: Press [1] plus code.
Check Faulted Zones: Lift cover on keypad. Press [2], then your code. For 8 seconds, lights become zone display lights.
Change code: Press [9], [Master Programming Code], Panel will beep twice, all lights will blink, [Press # corresponding to user number you want to add/change], Panel will beep 3 times, [Enter 5 digit new code], (shorter code can be entered by putting zeroes after code), after 5th digit panel will beep one long beep.
Power down panel: Open panel door. Slide power switch down (black switch located lower left corner of circuit board.)

Moose Z1100e with Alpha Keypad - Quick Reference

Arm	Press [LEAVE] or [STAY]. Then enter your CODE. If you selected [STAY], the keypad will ask you to confirm the interior and delay setting. Press [CONFIRM].
Disarm	Press [DISARM] and enter CODE.
Check Faulted Zones	If keypad says [ZONE(S) NOT READY], press [DISPLAY] to view faulted zones.
Smoke Reset	First, enter CODE to silence alarm. If a smoke detector is latched in alarm, the keypad will say [SUPERVISORY/TROUBLE]. You can press the scroll key to verify the trouble condition(s). Press [SMOKE RESET] and then your CODE.
Code Change	Press Menu Scroll Key 3 times. Press [PROGRAM]. Enter Master Programming Code. Press [CONTROL PANEL]. Press Function Number (01 for user code 1 -- thru -- 17 for user code 17). Press [FIND] when prompted. Display will show first digit of this users code. Enter each digit of desired new code. Codes must be 5 digits in length. If you want a shorter code, use trailing zeros (i.e. code 345 would be entered 34500.)
Chime Mode On/Off	Press Menu Scroll Key twice. Press [DAY MONITOR]. Enter CODE.
Force Arm Over Bad Zones	If enabled, keypad will give [LEAVE] and [STAY] options when displaying [ZONE(S) NOT READY]. Press [LEAVE] or [STAY]. Either [BYPASS] or [OVERRIDE] will display. Select this option. If more than one zone is faulted, scroll through faulted zones and bypass or override.
Power Down Panel	Open panel door. Press slide switch down located lower left corner of alarm panel circuit board.

Radionics 2000 series - Quick Reference

Arm: Press [9] to Arm All; Press [0] to Partial Arm

DisArm: Enter Code (If you are still in exit time, just press [CLEAR] to disarm.)

Check Faulted Zones: Faulted zones display automatically when faulted.

Smoke Reset: After silencing siren by entering code, press [3] + code to reset smokes.

Code Change: Enter [5], then [Old Code], then [New Code] same # of digits as old code, then [New Code] again.

Chime Mode On/Off: Press [7], keypad will display current setting.

To Change, enter code + [1] to turn off, [2] to turn on short beep, [3] to beep until CLEAR key is pressed, or [4] to beep until point closes.

Bypass Zone(s): Press [Zone #] + *.

Power Down Panel: Pull wire on NP7-12 battery, disconnect AC wire, upper left terminal on board.

Radionics 4112, 6112 - Quick Reference

Arm: Code + [ENT] key

(Shortcut: [COMMAND] [1] (Arm All), [COMMAND] [2] (Perimeter Instant), or [COMMAND] [3] (Perimeter Delay))

DisArm: Code + [ENT] key

Check Faulted Zones: Zone lights light when faulted. Slow blink means the zone is bypassed. Fast blink is alarm memory.

Smoke Reset: [COMMAND] [4] [7] (Disarm to silence siren first)

Code Change: [COMMAND] [5] + Old Code + [ENT] + New Code + [ENT] + New Code + [ENT]

Chime Mode On/Off: [COMMAND] [6] (Radionics calls it the "Watch Mode")

Force Arm Over Bad Zones: Code + [ENT] + [COMMAND] + [ENT]

(Do this all at once - will bypass faulted zone(s) automatically)

Power Down Panel: 1) - Pull wire on NP7-12 standby battery; 2) Disconnect terminal 1 AC wire.

Terminal 1 on a D4112 panel is far left bottom just like a Vista panel. On a D6112 panel, it is the far UPPER left corner terminal.

Radionics 7112 - Quick Reference

	This panel keypad has a MENU system which can be invoked by pressing [ENTER], then press [NEXT] to scroll thru options, pressing [ENTER] to select displayed option. The menu system is optional instead of using the "Command" system. You can do either.
Arm	[Code] + [ENTER] is the basic arming method. Shortcuts:
Disarm	[Code] + [ENTER]
Check Faulted Zones	Press [ENTER]. Press [NEXT] until "View Menu" is displayed. Press [ENTER]. Press [NEXT] until "View faulted Points" is displayed. Press [ENTER]. Press [NEXT] to scroll thru faulted points.
Smoke Reset	After resetting fire alarm with [CODE] + [ENTER], press [CMD][4][7] to reset smoke detectors.
Code Change	[CMD][5][5], Keypad displays [ENTER USER NUM]. Enter User number (not user code) + [ENTER], Keypad displays [ENTER NEW CODE]. Enter new code. Keypad displays [USER XX ZZZZZZ] (XX-User number, ZZZZZZ-User code). If correct, press [ENTER]. Keypad displays [PASSCODE CHANGED].
Chime Mode On/Off	[CMD] [6] turns on/off the "Watch Mode".
Force Arm Over Bad Zones	[Arm Method] Keypad will display [AREA X 01 FAULTS], Press [NEXT]. Keypad displays [FORCE/BYPAS ARM?]. Press [ENTER].
Power Down Panel	Remove one wire from NP7-12 battery. Remove one AC power wire from the panel. This is located bottom of panel, last 2 terminals on right side.
View Faulted Zones	Press [NEXT]. Keypad displays [AREA X 02 FAULTS]. Press [NEXT]. Keypad displays [FAULTED ZONE TEXT]. Press [NEXT], Keypad displays [NEXT FAULTED ZONE TEXT], etc. Press [CLR] to return to idle screen.

Radionics 8112 - Quick Reference

Arm:	[Code] Shortcuts: [COMMAND][1] Arms All; [COMMAND][2] Arms Perimeter w/ no delay; [COMMAND][3] Arms w/ delay.
DisArm:	[Code]
Check Faulted Zones	Press any numeric key [0-9] and keypad will scroll through faulted zones
Smoke Reset:	After silencing panel with [Code], press [COMMAND][4][7] to reset smokes.
Code Change:	[COMMAND][5][5], Old Code; New Code; New code again. D8112A and D8112E panels, the command is [COMMAND][5]. Most panels are D8112G models that use Command 55. Note: If you use Command 55, the user code will be a 6 digit number and the first 2 digits must stay the same (they are the user #). If you use Command 5, the user code will be a 5 digit number and the first digit must stay the same (it is the user #). This function can be disabled in programming, though it usually isn't.
Chime Mode On/Off:	[COMMAND][6] turns on/off the "Watch Mode".
Force Arm Over Open Zones:	If using [Code] to arm, hold last digit until panel arms over open zones. If using Command 1,2 or 3, press [COMMAND] and hold down the digit 1,2 or 3 until panel arms over open zones.
Power Down Panel:	Pull wire from NP7-12 battery, pull off wire on terminal 1, upper left corner of panel.
View Faulted Zones	If zones are faulted, keypad will display [NOT READY TO ARM]. Press any numeric key on the keypad to view faulted zones.

Radionics 9000/7000 series - Quick Reference

Arm	[Code] + [ENT] Shortcuts: [COMMAND][1] Arms All; [COMMAND][2] Arms Perimeter, entry zone is instant; [COMMAND][3] Arms Perimeter, entry zone delays.
Disarm	[Code] + [ENT]
Check Faulted Zones	Press any numeric key [0-9] and keypad will scroll through faulted zones
Smoke Reset	After silencing alarm with [Code] + [ENT], press [COMMAND][4][7] to reset smoke detectors.
Code Change	[COMMAND][5][5]; Enter Old Code + [ENT]; Enter New Code + [ENT]; Enter New Code Again + [ENT]. (To ADD a code, [COMMAND][5][6]. To DELETE a code, [COMMAND][5][3].)
Chime Mode On/Off	[COMMAND][6]
Force Arm Over Bad Zones	[Code]; Keypad displays [CHK AREA X]; Press [NEXT] thru the list of all faulted points OR just press [COMMAND]. [FORCE ARM?] will display at the end of the list. Press [ENT].
Power Down Panel	Pull one wire on NP7-12 battery in panel. Disconnect AC power by pulling wire on terminal 1, upper left corner of panel.
View Faulted Zones	Press ANY NUMBER KEY on the keypad. Faulted zones will scroll across keypad.

Other: - Quick Reference

Radionics D279	FBI

Panels: Will work with most panels, but almost always installed with Radionics D8112. This is NOT the main keypad. This is a self-contained alarm designed to be a one zone partition. It only controls its own area, not the whole alarm system. D279 User Guide Arm: 4 digit code Disarm: 4 digit code Check Faulted Zones: Faulted Zones display automatically. Lights: Change code: Press [BLANK] key, Enter OLD code once, NEW code twice. New code must also be 4 digits.	Panels: FBI XL-2 Installation Manual, User Manual Arm: 4 digit code Disarm: 4 digit code Check Faulted Zones: Alpha keypad (pictured here), faulted zones will automatically display. On LED keypad, zone lights of faulted zones will be lit. Change code: Press [CODE], enter 4 digit Master Code, enter [USER #] (1-6), enter new 4-digit code. Power down panel: 1) Pull one wire off of battery. 2) Unplug transformer, OR disconnect wire from terminal 24 or 25, lower right corner of circuit board.